Summer Sale Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: 70percent

Huawei H12-351_V1.0 HCIE-WLAN (Written) V1.0 Exam Practice Test

Demo: 48 questions
Total 163 questions

HCIE-WLAN (Written) V1.0 Questions and Answers

Question 1

Master NCE-Campuslnsight analyzes network issues during correlation analysis of poor-QoE clients, including coverage, interference throughput, and hardware issues.

Options:

A.

True

B.

False

Question 2

Which of the following statements are true about network optimization measures?

Options:

A.

Loops may occur if Ethernet cables are incorrectly connected to wall plate APs. In this case, loop detection can be enabled on the wired interfaces of APs to automatically block the interfaces once a loop is detected.

B.

It is recommended that the Beacon interval be adjusted based on the number of VAPs. A long interval increases the sleep time of STAs, and a short interval increases the air interface overhead.

C.

It is recommended that multicast packet suppression be enabled when multicast services are planned on the network.

D.

The rate limit for STAs can be set based on customer requirements. In most cases, 10 Mbps bandwidth for uplink and downlink traffic can support common Internet access applications.

Question 3

Smart roaming enables STAs to promptly roam to neighboring APs with better signals, improving the WLAN roaming experience. When the WAC detects a sticky STA. it immediately triggers a smart roaming policy to enable the STA to associate with a better AP.

Options:

A.

TRUE

B.

FALSE

Question 4

In mesh networking, APs have different roles. Drag the AP roles on the left to the role descriptions on the right.

Options:

Question 5

Which of the following is used for wireless positioning based on the signal propagation time?

Options:

A.

TOF

B.

TOA

C.

TDOA

D.

TDOF

Question 6

Which of the following user access authentication modes are supported In Huawel ' s CloudCampus Solution? (Select All that Apply)

Options:

A.

802. IX authentication

B.

MAC address authentication

C.

Portal authentication

Question 7

Which of the following advantages does BSS coloring provide in Wi-Fi 6? (Select All that Apply)

Options:

A.

Higher packet rate on the air interface

B.

Enhanced encryption on the air interface

C.

More efficient channel use

D.

Higher concurrency in high-density scenarios

Question 8

Which of the following are application scenarios of wireless technologies in the healthcare loT field?

Options:

A.

IoT hospital

B.

Mobile clinic system

C.

Healthcare network convergence

D.

Smart hospitalization

Question 9

To which of the following scenarios is radio calibration applicable?

Options:

A.

Enterprise office scenario

B.

Rail transportation scenario

C.

High-density scenario

D.

WDS or mesh backhaul scenario

Question 10

An intrusion prevention signature describes the characteristics of an attack on the network. The WAC detects and defends against attacks by comparing data flows with intrusion prevention signatures. Predefined signatures are those in the IPS signature database and cannot be created, modified, or deleted. Which of the following statements are true about the default action of a predefined signature?

Options:

A.

Allow: permits the packet to pass without recording a tog.

B.

Rate limiting: limits the rate of traffic and records a tog.

C.

Alert: permits the packet and records a tog.

D.

Block: discards the packet blocks the data flow to which the packet belongs, and records a tog.

Question 11

Which of the following statements about fingerprint-based positioning technology are true? (Select All that Apply)

Options:

A.

The positioning engine generates a virtual fingerprint library through calculations based on the AP deployment and environment information.

B.

Terminals learn from each other to form a fingerprint library that can be shared.

C.

APs collect surrounding environment information to form a fingerprint library.

D.

The fingerprint map is obtained through onsite information collection.

Question 12

The tunnel detection function can be used to check the tunnel status, for example, whether the tunnel is reachable. Which of the following mechanisms is used for GRE tunnel detection?

Options:

A.

TTL

B.

FEC

C.

Heartbeat

D.

Keepalive

Question 13

In 802. IX authentication using port-based access control, once a user is authenticated successfully on a port, subsequent users on this port can access the network without authentication. When the authenticated user goes offline, all other users are denied access to the network.

Options:

A.

True

B.

False

Question 14

Which of the following statements is false about STA roaming tracks on a Huawei WAC?

Options:

A.

If the values of In Rx/Tx, In RSSI, Out Rx/Tx, and Out RSSI are low, the signal coverage in this area may be abnormal.

B.

If the values of In Rx/Tx, In RSSI, Out Rx/Tx, and Out RSSI are good, the signal coverage in this area is excessively dense.

C.

It is unreasonable that the value of Out RSSI is lower than the signal strength of the next associated AP.

D.

It is reasonable that the value of Out Rx/Tx is lower than the signal strength of the next associated AR

Question 15

Which of the following types of non-Wi-R devices can be identified by Huawei APs? (Select All that Apply)

Options:

A.

Bluetooth device

B.

ZigBee device

C.

Game controller

D.

2.4 GHz wireless video and audio transmitter

Question 16

In a scenario where healthcare IoT solution is deployed, the planned data for an IoT card that needs to communicate with a host computer is as follows:

Which of the following configurations is correct to achieve the planned data?

A)

B)

C)

D)

Options:

A.

Option A

B.

Option B

C.

Option C

D.

Option D

Question 17

Which of the following statements about the home agent are true? (Select All that Apply)

Options:

A.

The home agent communicates with the gateway on the STAs1 home network at Layer 2.

B.

The home agent communicates with the gateway on the STAs ' home network at Layer 3.

C.

A home AP can function as a home agent of STAs.

D.

A home WAC can function as a home agent of STAs.

Question 18

iMaster NCE-Campuslnsight provides Intelligent radio calibration for high-load APs to increase the frequency bandwidth. This function applies to both 5 GHz and 2.4 GHz frequency bands.

Options:

A.

True

B.

False

Question 19

An IPv6 packet consists of three parts. Which of the following is not one of them?

Options:

A.

IPv6 basic header

B.

Upper-layer protocol data unit

C.

IPv6 extension header

D.

IPv6 reassembly header

Question 20

An LDAP directory is tree-structured and consists of multiple entries. Each entry has a unique distinguished name (DN). If the DM of a directory server is " CN=Stephen, 0U = Enterprise, OU = Huawei, DC=AD, DC=Huawei " , which of the following statements are false?

Options:

A.

DN specifies a path.

B.

The directory server is not an AD server.

C.

Stephen indicates a user or user group.

D.

The domain name of the directory server is Huawei

Question 21

Which of the following statements is true about Navi AC networking?

Options:

A.

The local AC and Navi AC must have the same service VLAN, SSID, user isolation mode, and authentication mode in their VAP profiles.

B.

The software versions of the local AC and Navi AC can be different.

C.

Dual-link backup can be deployed between the local AC and Navi AC.

D.

Inter-Navi AC roaming is supported.

Question 22

After traffic suppression is enabled on a Huawei WAC, the device monitors the rate of broadcast, multicast, and unknown unicast packets and compares the rate with the configured threshold. When the incoming traffic rate exceeds the configured threshold, the device discards the excess traffic.

Options:

A.

TRUE

B.

FALSE

Question 23

In large-scale campus network design, which of the following security technologies are recommended to be deployed at the access layer?

Options:

A.

Port isolation

B.

Broadcast storm suppression

C.

DHCP snooping

D.

IPSG and DAI

Question 24

In the Huawei public cloud scenario of Huawei ' s CloudCampus Solution, tenants log in to the cloud management platform through the Internet and connect to the platform through secure HTTPS access.

Options:

A.

TRUE

B.

FALSE

Question 25

A Wi-Fi RFID tag is a signal generator manufactured by tag vendors to help locate the objects. Which of the following types of tags can be located by Huawei devices?

Options:

A.

Hotspot tag

B.

AeroScout tag

C.

Location tag

D.

Ekahau tag

Question 26

Which of the following statements are true about the WLAN site survey In different typical scenarios? (Select All that Apply)

Options:

A.

In a classroom scenario. If the walls are made of reinforced concrete, the signal attenuation Is high. In this case, you are advised to test the attenuation during the site survey. Additionally, pay attention to the locations of ELV rooms in the teaching building.

B.

In an office scenario, the load-bearing columns and partitions affect the signal coverage. If an integrated ceiling is used, deploy APs near maintenance entrances. If a metal ceiling is used, mount APs on the ceiling or wall.

C.

In a ward-round scenario, high requirements are posed on the coverage field strength, roaming effect, and bandwidth. Determine the interference of medical equipment and the areas where Wi-Fi signals are not allowed.

D.

In a stadium scenario, the onsite environment is complex and cabling is difficult. Therefore, confirm with the property management company about ELV rooms and cabling. If the transmission distance is too long, consider deploying more switches. During the survey, focus on the interference between APs and AP mounting modes.

Question 27

Satellite positioning can achieve high positioning accuracy in both indoor and outdoor scenarios.

Options:

A.

True

B.

False

Question 28

No data is displayed on the Telemetry management page of (Master NCE-Campuslnsight. Which of the following are possible causes?

Options:

A.

Telemetry data reporting is no: configured on the device according to the guide.

B.

No license file is imported.

C.

The UTC lime on the device is inconsistent with that on iMaster NCE-Campuslnsight.

D.

The device is not added to iMaster NCE-Campuslnsight.

E.

The network between the device and iMaster NCE-Campuslnsight is disconnected.

Question 29

In a dual-link backup scenario, the active/standby link switchover mode is set to priority. When the active link recovers, the AP detects that the original active link has a higher priority and triggers a switchback. How many Echo intervals does the AP wait for before switching back to the original primary WAC?

Options:

A.

20

B.

10

C.

15

D.

5

Question 30

Radio frequency identification (RFID) is a non-contact automatic identification technology that automatically identifies objects. Which of the following components are included in a typical RFID system?

Options:

A.

Information processing system

B.

RFID tag

C.

Authentication server

D.

RFID reader

Question 31

As shown in the figure, STA_1 through STA_4 are associated with AP_1, and STA_5 is associated with AP_2. Assuming that the load balancing threshold is 2, the load difference threshold is 25%, and API and AP2 support a maximum of 10 STAs, which of the following statements are true? (Select All that Apply)

Options:

A.

The load percentage of AP_1 is 40%, and that of AP_2 is 10%.

B.

The load balancing mechanism needs to be enabled. Then some STAs are steered from AP_1 to AP__2.

C.

If load balancing is performed, the load percentage of AP_1 changes to 30%.

D.

The minimum load percentage is 10%, which is greater than the load difference threshold. Therefore, load balancing needs to be enabled.

Question 32

Which of the following Huawei ' s CloudCampus wireless positioning solutions provides the highest positioning accuracy while meeting specified network planning conditions?

Options:

A.

Bluetooth terminal navigation

B.

UWB positioning

C.

Wi-Fi terminal positioning

D.

Bluetooth tag positioning

Question 33

After RADIUS packet retransmission is triggered, if the device detects that the RADIUS server status is Down, the device marks the RADIUS server status as Down. If the maximum number of retransmissions has not been reached, which of the following will occur?

Options:

A.

The device retransmits the authentication request packet only once to the RADIUS server.

B.

The device retransmits the packet at most three more times, and stops retransmission once it receives a response packet or the maximum number of retransmissions is reached.

C.

The device continues to retransmit packets until it receives a response packet or the maximum number of retransmissions is reached.

D.

The device stops retransmission immediately.

Question 34

When planning WLAN outdoor coverage using external 2.4 GHz omnidirectional antennas with 3 dBi gain, what is the recommended coverage radius?

Options:

A.

80-100 m

B.

150-200 m

C.

30-50 m

D.

200-250 m

Question 35

During Portal authentication of a terminal, an authorization failure message is displayed when the user opens the push page using a browser. Which of the following could cause this problem?

Options:

A.

The authentication device does not support the authorization attribute delivered by the authentication server.

B.

The terminal attempts to access an HTTPS website before passing the authentication.

C.

No Portal server template is bound to the VLANIF interface of the access control device.

D.

No DNS server is configured in the pre-authentication domain.

Question 36

Which of the following technologies can be used to optimize multicast services on a WLAN?

Options:

A.

DHCP snooping

B.

Multicast-to-unicast conversion

C.

1GMP snooping

D.

MLD snooping

E.

Multicast CAC

Question 37

iMaster NCE-Campuslnsight comprehensively analyzes WLAN client access, displays success rates and time consumption of association, --------, and DHCP. It also provides issue analysis and optimization suggestions. (Enter lowercase letters.)

Options:

Question 38

Which of the following statements about WLAN roaming and signal strength Is false?

Options:

A.

Smart roaming can be enabled on the WAC to help ST As roam and associate with APs with better signals.

B.

Generally, a STA roams when it detects that the signal strength is less than -75 dBm.

C.

STAs can roam between WACs in dual-link HSB mode.

D.

In most cases, the signal strength of a STA should range from -45 dBm to -65 dBm.

Question 39

When a Huavrei WAC functions as an AAA server, it is called a local AAA server. A local AAA server supports authentication and authorisation but not accounting.

Options:

A.

TRUE

B.

FALSE

Question 40

Which of the following may be the reason why no data Is displayed on the telemetry management page of IMaster NCE-CampusInsight? (Select All that Apply)

Options:

A.

The network connecting devices and iMaster NCE-Campuslnsight Is faulty.

B.

Telemetry data reporting is not configured on devices according to the configuration guide.

C.

No license file is imported.

D.

Devices are not added to iMaster NCE-Campuslnsight.

E.

The UTC time of devices is inconsistent with that of iMaster NCE-Campuslnsight.

Question 41

An engineer configures the user CAC function on a Huawei WAC as follows. Which of the following statements are true about these configurations?

Options:

A.

When the SNR of a STA exceeds 10 dB, the STA is allowed to go online.

B.

CAC based on the number of STAs is used.

C.

CAC based on terminal SNR is used.

D.

When the SNR of a STA is lower than 10 dB, the STA is allowed to go online.

Question 42

The display sync-configuration compare command is executed on the backup WAC in HSB to check wireless configuration synchronization. Based on the command output, which of the following statements are true? (Select All that apply)

Options:

A.

This command is used to check whether the public configurations on two WACs are consistent after wireless configuration synchronization.

B.

The configuration of ssid-profile 2 exists on both the master and backup WACs.

C.

The configuration of vap-profile name 3 exists on the master WAC but not on the backup WAC.

D.

The configuration of vap-profile name 2 exists on the backup WAC but not on the master WAC.

Question 43

For multi-band APs, load balancing can be implemented among radios working on the same frequency band.

Options:

A.

TRUE

B.

FALSE

Question 44

The WAC supports the URL filtering functions. When users send HTTP or HTTPS requests for accessing URLs, URL filtering can be used to permit, generate alarms for, or block the requests. To match all URLs ended with aspx, such as www.example.com/news/solutions.aspx, www.example.com/it/price.aspx, and 10.1.1.1/sports/abc.aspx, which of the following URL matching items should be set?

Options:

A.

Aaspx

B.

#aspx

C.

*aspx

D.

$aspx

E.

.aspx

Question 45

Which of the following statements are true about management frames on a mesh network?

Options:

A.

In on-demand routing mode, when an MP receives a RANN frame and needs to create or update the route to the root node, the MP unicasts a PREP frame to the root node and broadcasts the RANN frame.

B.

In proactive routing mode, the source node broadcasts a PREQ frame to establish a route to the destination node. After an MP receives the PREQ frame, me MP responds with a PREP frame.

C.

After receiving the RANN frame, an MP decrements the TTL of the frame by one, updates the path metric, and broadcasts the RANN frame.

D.

The RANN frame is broadcast by the MPP periodically.

Question 46

Which of the following statements are true about DHCPvo packet types?

Options:

A.

A DHCFV6 client sends a Release message to the DHCPv6 server that assigns addresses to the client, indicating that the client will no longer use one or more of the obtained addresses.

B.

The DHCPv6 client sends a Confirm packet to any reachable DHCPv6 server to check whether the obtained IPv6 address is supported by the connected link.

C.

The DHCPv6 server sends an Offer packet to respond to the address allocation request and declare that it can provide DHCFV6 services.

D.

A DHCFM3 client sends a Discover packet to determine the location of a DHCPv6 server.

Question 47

Multicast addresses are Class D addresses, and can be used only as destination addresses but not source addresses of data packets.

Options:

A.

TRUE

B.

FALSE

Question 48

Either of the two APs that have established a mesh connection can send a Mesh Peering Close frame to the other AP to tear down the mesh connection.

Options:

A.

True

B.

False

Demo: 48 questions
Total 163 questions