Fortinet FCSS_LED_AR-7.6 Fortinet NSE 6 - LAN Edge 7.6 Architect Exam Practice Test

When FortiAuthenticator is used as anFSSO agentbased onsyslog, it must:

Parse incoming syslog messagesfrom devices (firewalls, WLAN controllers, VPN concentrators, etc.).

Extract identity fieldssuch as:

Username

IP address

Login/logout event indicators

Syslogmatching ruleson FortiAuthenticator define:

Which syslog messages are relevant (by facility, message pattern, or regex).

How to capture specific fields (username, IP, group, event type).

FortiAuthenticator then uses this parsed data toinject logon sessions into FSSO, so FortiGate can apply identity-based policies.

Thus, the role of syslog matching rules is exactly as described inC.

A: Group mapping is handled separately via directory groups / FSSO config, not directly by matching rules.

B: Enforcement of authentication policies is done on FortiGate, not directly by the matching rules.

D: While irrelevant logs can be ignored via rules, the primary purpose isparsing and extraction, not generic filtering.

When a FortiGate is deployed usingZero Touch Provisioning (ZTP)or auto-discovery:

FortiGate retrieves theFortiManager IP address(from DHCP Option 240, FortiCloud/ZTNA provisioning, or manual set).

The next step isnot UI authorizationor DHCP changes—it immediately attempts to form aFGFM (FortiGate–FortiManager) tunnel.

The FGFM protocol usesTCP port 541to establish a secure management channel.

FortiManager will still require manual authorization of the deviceinside FortiManager, but this occursafterthe tunnel is established.

Therefore, the first automatic action after retrieving the FMG address iscreating the secure FGFM tunnel on TCP/541.

From the exhibits:

The AP profile shows:

SSIDs: Tunnel | Bridge | Manual

The current setting isBridge, not Manual.

WhenBridgeorTunnelis selected, the AP profiledoes NOT automatically broadcast SSIDsunless the corresponding VAPs were explicitly mapped in the AP profile.

FortiManager SSID profiles are created, but unless these are explicitly applied underManual SSIDs selection, the AP will not broadcast any SSID.

Fortinet documentation states:

“To control which SSIDs an AP broadcasts, the AP Profile must have SSIDs set toManual, and the desired SSIDs must be selected.”

Therefore, to make the AP broadcast the intended SSIDs:

✔You must switch the SSIDs setting to Manual, and manually select the SSIDs (CompanyPrinters, Student01, Guest-CorpPort, PSK).

Why the other options are incorrect:

A. Adjust AP profile to avoid mixing bridge/tunnelMixed modes ARE supported. Not the issue.

B. Change platformThe platform (FAP231F) already supports all listed SSIDs.

D. Set transmit power mode to autoPower settings have nothing to do with SSID broadcasting.

The DHCP configuration shows:

set vci-match enable

set vci-string "FortiSwitch" "FortiExtender"

What this means

VCI = Vendor Class Identifier (DHCP option 60)

When vci-match is enabled, the DHCP server will only respond to DHCP requests from clients whose VCI string matches the configured vendor identifiers.

FortiSwitch and FortiExtender both send DHCP option 60 with:

"FortiSwitch"

"FortiExtender"

This is used in FortiLink deployments so only these devices receive IP addresses on the FortiLink network.

Therefore:

C. To connect, devices must match the VCI string; otherwise, they will not receive an IP address.

✔Correct.

This perfectly matches FortiGate FortiLink DHCP behavior.

Summary of incorrect options

A — Ignore FortiSwitch/FortiExtender

❌Opposite behavior.

B — Restrict based on hostname

❌VCI does NOT check hostname.

D — Reserve IPs

❌No reservation occurs; it's filtering, not reserving.

In FortiLink NAC for LAN Edge:

When a device first connects, it is placed into theonboarding VLAN.

NAC policies then classify the device (by MAC, OS, user, EMS tag, etc.).

If a NAC policy matches, the device may be moved to anaccess VLANorquarantine VLAN.

Ifno NAC policy matches, the device simplystays in the onboarding VLAN.

FortiOS / LAN Edge documentation describes the onboarding VLAN as thedefault VLAN for unknown or unclassified devices, until NAC policy evaluation moves them elsewhere.

From theWTP profile:

set handoff-rssi 30

set handoff-sta-thresh 30

config radio-1

set band 802.11n-2G

set vaps "Student01"

config radio-2

set band 802.11ac-5G

set darrp enable

set arrp-profile "arrp-default"

set vaps "Student01"

Key points:

Same SSID (Student01)is broadcast onboth APsand onboth bands(2.4 and 5 GHz).

handoff-sta-thresh 30 enablesclient load-balancingbetween APs:

When an AP radio hasmore than 30 associated clients, it starts rejecting new associations so that clients connect to a neighboring AP instead (as long as RSSI is still acceptable).

Current client counts:

AP1:32 clients on 5 GHz, 22 on 2.4 GHz

AP2:12 clients on 5 GHz, 20 on 2.4 GHz

So on 5 GHz:

AP1’s 5-GHz radioexceedsthe 30-client threshold (32 > 30) → it will try topush new clients away.

AP2’s 5-GHz radio iswell belowthe threshold (12 clients) and will happily accept new clients.

The new dual-band client is seen at:

–33 dBmby AP1

–43 dBmby AP2

Even though AP1 has the stronger signal, its 5-GHz radio is already overloaded according to the configured threshold, so AP1 will refuse association attempts from that client. The client will then associate toAP2’s 5-GHz radio, which:

Hasfewer clients(better airtime per device), and

Still has an acceptable signal (–43 dBm is easily usable on 5 GHz).

That matches optionCexactly.

Other options are incorrect because they ignore the configuredclient-load-balancing thresholdsand assume association based purely on RSSI or prefer 2.4 GHz, which is not what this profile is tuned to do.

From the exhibits:

FortiSwitch Ports viewshows:

port2

Mode: Static

Native VLAN: Students

Allowed VLANs: quarantine.fortilink (quarantine)

NAC policy “Training”:

Switch FortiLink: fortilink

Category:Device

Matching criteria:

MAC Address: 70:88:6b:8c:4b:0e (enabled)

Operating System:Linux(enabled)

Switch Controller Action:

Assign VLAN = Students

Bounce Port = enabled

Design intent:

Device with that MAC + OS Linux, when plugged intoport2, should be dynamically moved to VLANStudentsby the NAC policy.

Why it doesn’t work now

On FortiLink NAC,dynamic NAC decisions only apply on ports whose “Access Mode” is set to NAC:

NAC mode = FortiGate controls theonboarding VLAN, evaluates NAC policies, and then dynamically reassigns the switch port VLAN (access, quarantine, etc.).

Static mode(what we see on port2) means the port just uses its configurednative/allowed VLANs, andno NAC classificationhappens.

Right now:

port2 is astatic access portwith Native VLAN = Students.

The NAC policy exists, butFortiSwitch is not in NAC enforcement mode on that port, so the policy is never evaluated for traffic on port2.

Therefore, themissing configurationis:

Setport2toNAC mode(sometimes called “Access mode: NAC” or “NAC LAN edge port”).

Once port2 is changed to NAC mode:

Device initially lands in the onboarding/quarantine VLAN.

FortiGate collects device info (MAC, OS, etc.).

NAC policy “Training” matches MAC + Linux.

Switch controller actionAssign VLAN = Studentsis applied.

Port is bounced (if configured), bringing the device back up in VLAN Students.

Why the other options are wrong

B. MAC or OS misconfigured

Possible in general, but the question asks forwhich configuration is missing, and the exhibits clearly focus on port mode. Also, even with wrong MAC/OS, the port would still be in NAC mode; here NAC isn’t even active.

C. Port Policy mode

Port policy (edge/trunk) is separate from NAC; NAC requires the specificNAC access mode.

D. Students VLAN should be Allowed VLANs instead of Native VLAN

For an access port, having Students as thenative VLANis correct. NAC policy’s Assign VLAN will set that as access VLAN; no need to make it an allowed trunk VLAN.

The VAP configuration clearly showsVLAN pooling using WTP-groups:

set vlan-pooling wtp-group

config vlan-pool

edit 101

set wtp-group "Floor_1"

edit 102

set wtp-group "Office"

How VLAN assignment works in this mode

VLAN-pooling with wtp-group modemeans:

Each AP group (WTP group) is tied to exactly one VLAN in the pool.

The FortiGate doesnot load balanceVLANs.

Instead, VLANs are mappedper AP group, not per client.

Now verify each answer option:

A. FortiGate will load balance clients using VLAN 101 and 102...

❌Incorrect.

FortiGatedoes NOT load-balance clientswhen vlan-pooling is set towtp-group.

Each AP group receivesonly the VLAN mapped to it.

B. All clients in the Corp zone get IPs from 10.0.20.0/24

❌Incorrect.

In the Wi-Fi zone table, onlyCorp.102has an IP subnet:

Corp.101 →0.0.0.0/0.0.0.0(no IP assigned → clients get no DHCP)

Corp.102 →10.0.20.1/255.255.255.0

Thus, clients associated to VLAN 101cannotget IPs.

C. Clients connecting to APs in the Floor_1 group cannot receive an IP address

✔Correct.

Reason:

Floor_1 WTP-group → VLAN101

VLAN 101 hasno IPin the Wi-Fi table →0.0.0.0/0.0.0.0

No DHCP =Clients receive no IP address

D. Clients connecting to APs in the Office group will be assigned to VLAN 102

✔Correct.

Reason:

Office WTP-group maps to VLAN102

VLAN 102 has subnet10.0.20.0/24

So Office group clients get an IP in that range

In this design, FortiAuthenticator receivesRADIUS accounting (RSSO) messages, looks up the user in LDAP to get group information, theninjects FSSO logon eventstoward all FortiGate devices.

From the exhibits we know:

FortiAuthenticatoris receiving RADIUS accountingfrom the RADIUS server.

LDAP queries are successful and return group membership.

But FortiGatedoes not receive FSSO logons, so identity-based policies are not applied.

For FortiAuthenticator to create an FSSO logon, the RADIUS accounting record must be correctlyparsed into at least:

Username

Client IP address

These are mapped from the RADIUS attributes in theRADIUS Accounting SSO clientconfiguration (for example, User-Name and Framed-IP-Address). If these are not defined or mapped incorrectly, FortiAuthenticator can see the accounting packet butcannot build a valid FSSO session, so no update is sent to FortiGate.

Thus the most likely root cause is:

✔The RADIUS Username and Client IPv4 attributes are not correctly definedfor that RADIUS Accounting SSO client (optionA).

Other options conflict with the scenario:

B– LDAP is already successfully returning groups.

C– FSSO user group attribute is separate; even without it, FSSO logons would still be created (just without group mapping).

D– The interfaceisreceiving RADIUS accounting, so it is clearly enabled.

The SSL-VPN configuration hasRequire Client Certificateenabled. When this is enabled, FortiOS performs two checks:

Normal user authentication(username/password or PKI user)

Additional client certificate check– the client certificatemust be signed by a CA that FortiGate trusts

FortiOS documentation for “SSL VPN with certificate authentication” states:

“The client certificate only needs to be signed by a known CA in order to pass authentication.”

“The CA certificate is the certificate that signed both the server certificate and the user certificate… The CA certificate is available to be imported on the FortiGate.”

The debug output shows key lines:

__quick_check_peer-CA does not match.

Issuer of cert depth 0 is not detected in CMDB.

This tells us:

FortiGatedoes see the user’s certificate,

Butcannot find the issuing CAin its local CA certificate store (“CMDB” = configuration database).

This means theCA that signed the user certificate has not been importedinto FortiGate.

Now evaluate the options:

A. Enable Redirect HTTP to SSL-VPN– affects only redirection from HTTP to HTTPS; it has nothing to do with certificate validation.

B. Import the CA that signed the SSL VPN Server Certificate– the server certificate is already working (the portal comes up) and its CA is not what the debug complains about; the error is about thepeer (user) certificate. Often the same CA signs both, but the failing check specifically says the issuer of the client cert is not in CMDB.

C. Set the user certificate as the Server Certificate– incorrect; server and client certificates serve different roles.

D. Import the CA that signed the user certificate to FortiGate– this directly addresses the debug error and aligns with the documented requirement that the CA which issued the user certificate must be known to FortiGate.

WithAD machine authenticationvia FortiAuthenticator:

When a machine successfully authenticates, FortiAuthenticator records:

Machine account / identity

MAC addressof the device

Associated IP and session info

To handle sleep/hibernation:

FortiAuthenticator keeps acache of authenticated MAC addressesfor a configured timeout.

When the device wakes up and sends traffic again, FortiAuthenticator/FSSO can still treat it as authenticated as long as its MAC is in cache, so access is maintained without forcing a full machine re-auth immediately.

This matches optionD.

A(guest VLAN) is not the standard behavior here.

B(WoL) is unrelated.

C(IP-based) would break as IPs can change; MAC-based caching is what’s used.