What is the maximum supported latency for a VPLEX Metro implementation?
Following EMC best practices, what information is required to register a VPLEX on an ESRS portal?
Refer to the Exhibit.
Based on this diagram of a single VPLEX engine, which protocol is represented by "A"?
What is the purpose of VPLEX Witness in a Metro environment?
Which VPLEX component can determine the difference between a partition and a site failure of a VPLEX Metro configuration?
Refer to the exhibit.
You have created a Distributed Device in a VPLEX Metro. You want to confirm you have chosen the correct volumes before performing a mobility job across clusters. You will be moving the device to cluster 1.
Which object will be the source for this operation?
Which VPLEX component is configured with a public IP address during the installation process?
You are configuring an FC Switch for a VPLEX implementation using VS2 engines. What is the required speed setting for the switch ports connected to the VPLEX FE ports in order to achieve the maximum throughput of VS2 engines?
What mobility operation must be performed to defragment storage volumes?
What is required of an ESX host for the Witness to be installed?
Refer to the exhibit.
A customer wants to implement a VPLEX Metro High Availability Cross Connect implementation between their two campus sites. What round-trip latency time requirement must be met between Site A and Site B?
Refer to the exhibit.
After a power disruption of 20 seconds in a VPLEX environment, the output of the "vault status" command shows no vaulting processes.
Why did this occur?
What option must be set for a consistency group to continue synchronization without manual intervention, once connectivity is restored?
You are administering a VPLEX Metro configuration. When is it necessary to create a logging volume?
You are preparing a site for a large Metro VPLEX cluster. The storage administrator wants to prepare the storage network configuration and needs to ensure easy troubleshooting of storage path faults.
How many WAN-COM zones per fabric will need to be created?
Which type of statistics is used to track latencies, determine median, mode, percentiles, minimums and maximums?
How do you verify that the VPLEX upgrade has completed successfully?
Refer to the exhibit.
The customer deleted ext_2 on a 20 GB LUN in order to make an extent of 10 GB. Why is the customer unable to create a 10 GB extent?
A customer is moving some VMAX devices under a VPLEX Local and is using PowerPath as multipath software.
What is the SCSI product ID assigned to VPLEX volumes?
Refer to the exhibit.
You are implementing a VPLEX Metro configuration, and some BE ports are not logged into the fabric.
Which VPLEX command should be performed?
What is the maximum number of Virtual Volumes that can be created in a VPLEX Version 5 Cluster?
A customer has just introduced a new VPLEX cluster into their storage environment with numerous existing storage arrays. They need to present the host's existing data from the VPLEX cluster.
Which method would you use to perform this operation?
IT security just implemented new security policies at a customer site. When VPLEX Management Server sends SYR reports to an ESRS gateway nothing is received at the gateway.
What action did IT security take that would cause this?
Refer to the exhibit.
You have created a Distributed Device in a VPLEX Metro. You want to confirm the volumes before performing a mobility job within the cluster. You will be moving the device to cluster 1.
Which object will be the source for this operation?
A customer has a VPLEX Metro installed. They asked you to recommend a method to non-disruptively move Virtual Volumes from a storage array at Cluster 1 to a storage array at Cluster 2.
What would you recommend?
VPLEX ndu pre-check command reports a time drift between directors and the Management Server. How must the NDU be performed?
When creating logging and metadata volumes, which LUN requirement applies to both?
What is the role of the port with the WWN 5000144270061010 on a VS2 engine?
An EMC customer wants to add a mirror to a VPLEX Local RAID 0 device. Which RAID type is created after the device attach-mirror command is issued?
A customer is verifying the host environment before scheduling a VPLEX NDU. According to EMC best practices, which PowerPath load-balancing policy is applied by default to all platforms?
A customer created a local RAID-0 virtual volume and decided that they require increased data protection by introducing a distributed virtual volume. What is the best method to convert this virtual volume without introducing any downtime to the host?