Weekend Sale Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: 70percent

Cisco 300-815 Implementing Cisco Advanced Call Control and Mobility Services (CLACCM) Exam Practice Test

Demo: 66 questions
Total 221 questions

Implementing Cisco Advanced Call Control and Mobility Services (CLACCM) Questions and Answers

Question 1

Refer to the exhibit.

A collaboration engineer is troubleshooting an issue where external callers cannot leave voicemail messages. Also, internal users report hearing the reorder tone (fast busy) when they attempt to retrieve voicemail messages from their Cisco IP phones. Which action resolves the issue?

Options:

A.

Ensure that Cisco UCM can resolve the destination address via DNS.

B.

Start the Cisco Call Manager service at the destination.

C.

Ensure that the SIP Trunk Security Profile is configured to use UDP for transport.

D.

Verify that the correct port numbers are used for the SIP trunk.

Question 2

A customer is using a SIP trunk to route calls to ITSP to decrease the possibility of downtime, the customer invested in a failover device How does the customer ensure reachability to ITSP, so that if one device on ITSP fails, the calls will be routed to another device?

Options:

A.

Enable transmit security status on the SIP security profile

B.

Enable ANAT on the SIP profile.

C.

Monitor the link using network management toots, and if it fails, manually change the routing to another working device.

D.

Enable SIP Option Ping on the SIP profile.

Question 3

Refer to the exhibit.

A Cisco Unified Border Element continues to send 180/183 with the required: 100rel header to Cisco UCM. and the call eventually disconnects How is the issue resolved?

Options:

A.

Enable 'SIP ReI1XX Options* and -Early Offer Support" on the SIP Profile Configuration Page in Cisco UCM.

B.

Enable *Early Offer support for voice and video calls" on the SIP Profile Configuration Page in Cisco UCM.

C.

Disable "SIP Rel1XX Options* and 'Early Offer Support* on the SIP Profile Configuration Page m Cisco UCM.

D.

Disable "Send send-receive SDP in mid-call INVITE* on the SIP Profile Configuration Page in Cisco UCM.

Question 4

A new Cisco UCM deployment is configured, and now the customer requires a set of 10 DNSs to park the calls starting with 8. The users must use the softkey to park the call. Which configuration must be performed to achieve this requirement?

A)

B)

C)

D)

Options:

A.

Option A

B.

Option B

C.

Option C

D.

Option D

Question 5

An engineer is configuring Cisco UCM lo forward parked calls back to the user who parked the call if it is not retrieved after a specified time interval. Which action must be taken to accomplish this task?

Options:

A.

Configure device pools.

B.

Configure service parameters

C.

Configure enterprise softkeys.

D.

Configure class of control.

Question 6

An SRST site must use pickup functionality on the Chicago remote site to allow the users to take incoming calls. The pickup command is configured under the call-manager-fallback section on the SRST router What are two results of that configuration? (Choose two.)

Options:

A.

The PickUp soft key is on all SRST phones.

B.

The GPickUp soft key is on all SRST phones.

C.

Calls that come into one directory number can be picked up from another directory number.

D.

Calls that come into a Cisco UCM registered phone can be picked up by a SRST phone.

E.

Calls that ring an unassigned directory number are forwarded to the auto-attendant.

Question 7

Management wants to change the initial announcements for one of the existing call hunt groups. A new set of announcement audio file was provided. Which two configuration steps must the administrator take to accomplish this change? (Choose two.)

Options:

A.

Identify the MOH audio source ID associated to one of the line group member’s “Network Hold MOH Audio Source”.

B.

Identify the MOH audio source ID associated to “Network Hold Source & Announcements” under the Queuing section of the hunt pilot.

C.

Identify the configured announcement names to change under the MOH audio source section, then upload the new files to the respective announcements under the Announcement section.

D.

Identify the MOH audio source ID associated to one of the line group member’s “User Hold MOH Audio Source”.

E.

Identify the configured announcement names to change under the Announcement section, and assign the uploaded files to the Queueing section of the hunt pilot.

Question 8

Why would RTP traffic that is sent from the originating endpoint fail to be received on the far endpoint?

Options:

A.

The far end connection data (c=) in the SDP was overwritten by deep packet inspection in the call signaling path.

B.

Cisco Unified Communications Manager invoked media termination point resources.

C.

The RTP traffic is arriving beyond the jitter buffer on the receiving end.

D.

A firewall in the media path is blocking TCP ports 16384-32768.

Question 9

When configuring hunt groups, where does the administrator add the individual directory numbers that should be part of the group?

Options:

A.

route group

B.

line group

C.

hunt list

D.

hunt pilot

Question 10

An administrator is configuring Meet-me conferencing in a Cisco UCM deployment and has created the Meet-me number and ensured that it is in a partition accessible by all devices. Which two additional steps must the administrator perform? (Choose two.)

Update the softkey template on all phones to ensure that they contain the Meet-me softkey.

Options:

A.

Ensure that conferencing-initiating devices are using a media resource group list that contains at least one Cisco UCM conference bridge.

B.

Enable Meet-me conferencing In enterprise parameters.

C.

Ensure that all devices have G.729 enabled.

D.

Disable Early Media on the SIP profile of all devices that will use Meet-me conferencing.

Question 11

The company implemented Cisco Unified Mobility on the Cisco UCM. The users are satisfied and can transfer voice calls between devices. Mobile users want to extend the timer that controls thetime given to pick up a voice call on an IP phone from 4 to 6 seconds. Which configuration change satisfies this requirement?

Options:

A.

Change the "Maximum Wait Time for Mobility Pickup" setting from 4 to 6.

B.

Change the "Maximum Wait Time for Desk Pickup" setting from 4 to 6.

C.

Change the "Maximum Wait Time for Mobility Pickup" setting from 4000 to 6000.

D.

Change the "Maximum Wait Time for Desk Pickup" setting from 4000 to 6000.

Question 12

The administrator of ABC company is troubleshooting a one-way audio issue for a call that uses H.323 protocol (slow-start mode). The administrator requests that you provide the IP and port information of the Real- Time Transport Protocol traffic that had the one-way audio call.

You gather the H.225 and H.245 messages for one of the one-way audio calls. Where can you find the RTP IP and port information for both sides? (Note: This call flow has not invoked any media resources like MTP or transcoders).

Options:

A.

H.245 Terminal Capability Set

B.

H.245 Open Logical Channel

C.

H.225 Connect

D.

H.245 Open Logical Channel Ack

Question 13

If all patterns below are configured in Cisco Unified Communications Manager which would be used when dialing the pattern “123”?

Options:

A.

12!

B.

12X (urgent priority set)

C.

1XX (urgent Priority Set)

D.

12[2-5]

Question 14

What are two functions of the metadata in SIP recording? (Choose two.)

Options:

A.

includes the details of the application media stream

B.

contains the cryptographic context of the SRTP passthrough calls

C.

identifies the session and media association time

D.

carries the Agent Statistics Report

E.

carries the communication session data (audio and video calls) that describes the call to the recording server

Question 15

The Cisco Unified Communications Manager Dialed Number Analyzer allows analysis of calls from which two devices? (Choose two.)

Options:

A.

translation patterns

B.

device pools

C.

CTI ports

D.

CTI route points

E.

IP phones

Question 16

A newly deployed site in Pennsylvania uses SIP-to-SIP legs on a Cisco Unified Border Element. The administrator wants to match the incoming dial peer based on the calling number. Which configuration is needed in the dial-peer?

Options:

A.

answer-address

B.

incoming called-number

C.

destination calling

D.

destination-pattern

Question 17

Calls are not working when sent from a Cisco Unified Border Element to a service provider. After investigating the logs, the engineer notes that the Cisco Unified Border Element is sending the extension only. How is the issue addressed in the configuration?

Options:

A.

voice class request sip-header diversion

B.

sip-header contact modify

C.

voice class request sip-header modify

D.

request invite sip-header diversion modify

Question 18

An administrator wants to use the Call Queuemg feature on Cisco UCM to allow new customers to wait in the queue while other agents are not available to take their call. Which configuration step enables this feature?

Options:

A.

Call Routing > Route/Hunt > Call Park

B.

Call Routing > Route/Hunt > Hunt Pilot

C.

Call Routing > Route/Hunt > Line Group

D.

Call Routing > Route/Hunt > Hunt List

Question 19

An administrator manages an environment with mobile users who commonly move between locations and take IP phones to remote sites. When mobile users are at one of the sites, users report issues with call quality, such as the audio cutting in and out. In addition, the affected area has a low bandwidth connection compared to other sites, so the administrator has put these devices in a region with an inter-region restriction of 8 kbps per call. Which feature must the administrator configure to mitigate the issue?

Options:

A.

Location Bandwidth Manager

B.

Extension Mobility

C.

Device Mobility

D.

Extension Mobility Cross Cluster

Question 20

Which elements does Cisco cloud mobility for collaboration include?

Options:

A.

Cisco Webex Collaboration Cloud Services

B.

Cisco Collaboration Cloud

C.

Cisco Collaboration Cloud and Cisco Webex Collaboration Cloud Services

D.

Cisco Collaboration Cloud and Cisco Mobile and Remote Access Collaboration Cloud Services

Question 21

An engineer configures several calling party transformation patterns in Cisco UCM so that calling numbers are shown in the +E.164 format. The route patterns match seven-digit internal numbers and prefix the numbers with 1408. The SIP trunk matches 1408XXXXXXX and prefixes the number with +. When users make outbound calls, the calling number still shows as seven digits. What is the cause of this problem?

Options:

A.

The calling transformation on the SIP trunk is applied first, and then the calling transformation on the route patterns is applied.

B.

Calling transformations cannot be configured on both route patterns and a SIP trunk.

C.

The calling transformation on the route patterns is ignored because there is already a calling transformation on the SIP trunk.

D.

The engineer must also apply a calling transformation at the route group details level.

Question 22

Refer to the exhibit. A company is using Microsoft Teams with Cisco Unified Border Element integration, but the administrator sees a one-way audio issue with Microsoft Teams. The administrator must modify the SIP profile to send the proper information on the SDP for IP address for media to match the internal and external interface. Which set of commands resolves the issue?

Options:

A.

voice class sip-profiles 1

request INVITE sdp-header Connection-Info modify “2\.76\.1” “2.78.1”

B.

voice class sip-profiles 1

request INVITE sdp-header Session-Owner modify “27\.0\.0” “27.3.0”

C.

voice class sip-profiles 1

request INVITE sdp-header Connection add “2\.76\.1” “2.78.1”

D.

voice class sip-profiles 1

request INVITE sdp-header Audio-Attribute modify “2\.76\.1” “2.71.1”

Question 23

When a third-party SIP Phone System is dialed inbound across a Cisco Unified Border Element, DTMF is failing. The third-party vendor accepts only out-of-band DTMF. Which configuration should be added to the outgoing dial peer to resolve this issue?

Options:

A.

dtmf-relay h245-signal

B.

dtmf-relay rtp-nte

C.

dtmf-relay cisco-rtp

D.

dtmf-relay sip-kpml

Question 24

Some users report poor quality when they travel to another continent and make calls. This issue applies only to one continent and not to others, where typically the dialing is fast and quality is clear. Users experience the same result at home when they call the same numbers in that specific continent. It seems like some users do not exist in the correct PSTN gateway when making calls to a specific country. The company is using TEHO to save on the cost of international or long-distance calling.

They are also using a globalized dial plan. What is the cause of the issue?

Options:

A.

CUBE is not configured forTEHO in the specific country

B.

A local route group is not added to the route pattern.

C.

The users are missing this specific gateway at the device pool level.

D.

Regions in Cisco UCM are not configured correctly.

Question 25

The company Cisco UCM cluster has two different gateways for off-net calls. The current configuration uses 9 as a prefix to get to the main gateway. The secondary gateway is for any calls that start with 9713, but this is not yet configured. The admin does not want to add more route patterns other than the current 9 prefix for the gateway to the Cisco UCM. How must the Cisco UCM be configured to meet the requirements?

Options:

A.

Configure two CSSs. then add a translation pattern with the secondary CSS to send calls with 9713 to the secondary gateway.

B.

Configure two partitions and two CSSs, then add a translation pattern with the secondary CSS to send all calls with 9713 to the secondary gateway.

C.

Create a Standard Route Group to dynamically route calls with prefix 9713 to the secondary gateway.

D.

Configure a Route Group and a Route List to send calls with prefix 9713 to the secondary gateway.

Question 26

Refer to the exhibit.

While troubleshooting call failures on the Cisco Unified Border Element, an administrator notices that messages are being sent to the service provider, but there is no response The administrator later learns that this SIP provider does not support PRACK. Which header should be removed from the SIP message to resolve this issue?

Options:

A.

Content-Disposition: session:handling=required

B.

Require 100rel

C.

Contact

D.

Content-Type: application/sdp

Question 27

Refer to the exhibit.

A company needs to ensure that all calls are normalized to ♦ E164 format. Which configuration will ensure that the resulting digit string ♦14085554001 is created and will be routed to the E.164 routing schema?

Options:

A.

Called Party Transformation Mask of + 14085554XXX

B.

Called Party Transformation Mask of ♦1408555[35)XXX

C.

Calling Party Transformation Mask of +1408555XXXX

D.

Calling Party Transformation Mask of +14085554XXX

Question 28

A user reports that when they attempt to log out from the Cisco Extension Mobility service by pressing the Services button, they cannot log out. What is the most likely cause of this issue?

Options:

A.

The Cisco Extension Mobility service has not been configured on the phone.

B.

There might be a significant delay between the button being pressed and the Cisco Extension Mobility service recognizing it. It would be best to check network latency.

C.

The user device profile has not been assigned to the user.

D.

The user device profile is not subscribed to the Cisco Extension Mobility service.

Question 29

Refer to the exhibit.

A collaboration engineer investigates an issue where the user calls that match the local Jabber domain are routed back to Cisco UCM. Which action resolves this problem?

Options:

A.

Check the check box to block the pattern for the local domain.

B.

Create another route SIP pattern for the local domain with the block pattern selected.

C.

Create a translation pattern to block calls to the local domain.

D.

Create a transformation pattern to block calls to the local domain.

Question 30

What is a component of Cisco Unified Mobility?

Options:

A.

Unified IVR

B.

Mobile Connect

C.

Smart Client Support

D.

Single Number Connect

Question 31

A company with only 15 users needs to have a phone system without deploying dedicated servers for this purpose. Using the local Cisco router with Cisco UCME capabilities, which configuration is needed to support SIP phones?

Options:

A.

voice-register ephone

B.

ephone

C.

voice-register pool

D.

voice-register SIP

Question 32

Which action is correct with respect to toll fraud prevention configuration in the Cisco Unified Communications Manager Express?

Options:

A.

Configure Direct Inward Dial for Incoming ISDN Calls with overlap dialing.

B.

Configure IP Address Trusted Authentication for Incoming VoIP Calls.

C.

Configure the command no ip address trusted authenticate under “voice service voip”.

D.

Enable Secondary Dial tone on Analog and Digital FXO Ports.

Question 33

An engineer must configure call queuing under a Hunt Pilot. After the engineer receives the audio file that will be played to callers during queuing, which two steps should be taken to complete the configuration? (Choose two.)

Options:

A.

Assign the uploaded audio file to the hunting Line Group member's "User Hold MOH Audio Source

B.

Assign the uploaded audio file to the hunting Line Group member's "Network Hold MOH Audio Source".

C.

Upload the audio file in "TFTP File Management” via OS Administration GUI

D.

Assign the uploaded audio file to "Network Hold MOH Source & Announcements" under Hunt Pilot's Queuing section.

E.

Upload the audio file in "MOH Audio File Management" via CM Administration GUI

Question 34

When route patterns are defined as precisely as possible on a Cisco UCM, the control and reliability of the calling plan is increased. A route pattern must be added to support calls to this number range: 9135200 to 9135205. The calls are on-net and no translation patterns are configured. Which configuration meets these requirements?

Options:

A.

913520[012345]

B.

913520X

C.

913520[1–5]

D.

913520!

Question 35

An administrator deployed a third-party H.323 gateway in a voice environment, but users report call failures when using features like call hold or call transfer. What are two reasons that these features fail? (Choose two.)

Options:

A.

The CSS of the transfer initiating line does not contain the partition of the supplementary feature extension (DirectTransfer or MoH Number).

B.

The MTP that is configured for use within the H.323 gateway configuration is configured as a trusted source, but the third-party gateway does not trust the signing root CA certificate of the MTP certificate.

C.

The MTP does not support the negotiated codec, and media renegotiating during the call is not supported.

D.

The Media Resource Group List of the H.323 gateway contains only transcoders and conference bridges but no MTP.

E.

The third-party gateway does not support supplementary features, so Media Termination Point (MTP) must be inserted.

Question 36

An engineer needs to deploy the local route group feature to a Cisco UCM server by using the standard local route group. For each device pool, the engineer needs to specify a different PSTN access for emergency calls. What must the engineer do?

Options:

A.

Add a new standard local route group. Select a route group as the new standard local route group in Device Pools. Create a route pattern of 911 that points to a route list that contains the new standard local route group.

B.

Create a new local route group name. In Device Pools, select a route group for that new local route group. Create a route pattern of 911 that points to a route list that contains the new local route group.

C.

Set a new local route group name. Select a route group as the new local route group in Device Pools. Create a route pattern of 911 that points to the new local route group.

D.

Add a new standard local route group. Select a route group as the new standard local route group in Device Pools. Create a route pattern of 911 that points to the new standard local route group.

Question 37

Which call pickup feature allows users to pick up incoming calls in a group that is associated with their own group?

Options:

A.

Other Group Pickup

B.

BLF Call Pickup

C.

Group Call Pickup

D.

Directed Call Pickup

Question 38

An organization configures a SIP trunk in Cisco UCM to connect to another system. These requirements must be met:

1. Use a specific IP address for SIP signaling.

2. Encrypt the signaling traffic.

3. Restrict which devices can use the SIP trunk. 4 Simplify SIP signaling.

Drag and drop the Cisco UCM configuration steps from the left onto the order on the right to achieve these goals.

Options:

Question 39

Refer to the exhibit.

An administrator is troubleshooting why users are not hearing audio when dialing long distance numbers across their Cisco Unified Border Element. The customer’s carrier has a requirement that dialing long distance requires an access code to be entered. Looking at the exhibit, what two actions can be taken to correct signaling? (Choose two.)

Options:

A.

Enable PRACK.

B.

Enable Early Offer on the Cisco Unified Border Element.

C.

Enable the supplementary-service media-renegotiate command.

D.

Enable Media Flow Around

E.

Enable Mid-Call Signaling Consumption.

Question 40

A company is using Cisco Jabber on-premises to make B2B calls on video. The calls are using Cisco Expressway-C and Expressway-E and have been configured in Cisco UCM to be able to call any URI on the internet. The Jabber client also has voice enabled and must be able to call local, regional, and international numbers. Where must Cisco UCM be configured to meet this requirement for URI dialing?

Options:

A.

Enter "!#" in the route pattern section tied to a route group and list.

B.

Enter "*" in the SIP route pattern.

C.

Enter "!#" in the SIP route pattern.

D.

Enter ".*" in the route pattern section tied to a route group and list.

Question 41

An engineer is configuring a Cisco Collaboration system for SIP endpoints and must enable Survivable Remote Site Telephony for these endpoints. Which code completes this configuration on the SRST gateway?

A)

B)

C)

D)

Options:

A.

Option A

B.

Option B

C.

Option C

D.

Option D

Question 42

An administrator must control the number of calls to a remote specific site to reduce bandwidth constraints. The users on that remote site report bad quality of the calls passing through that WAN link. Which action must the administrator take in Cisco UCM to resolve the issue?

Options:

A.

Use RSPV.

B.

Use Location Bandwidth Manager.

C.

Use Expressway deployment.

D.

Use Call Allow Controller.

Question 43

After configuring a Cisco CallManager Express with Cisco Unity Express, inbound calls from the PSTN SIP trunk receive a ring tone for 20 seconds and then a busy signal instead of voicemail. Which configuration fixes this problem?

Options:

A.

Router(config)# voice service voip

Router(conf-voi-serv)#allow-connections h323 to h323

B.

Router(config)#dial-peer voice 2 voip

Router(config-dial-peer)#no vad

C.

Router(config)# voice service voip

Router(conf-voi-serv)#allow-connections voice-mail mod

D.

Router(config)# voice service voip

Router(conf-voi-serv)#no supplementary-service sip moved-temporarily

Question 44

Refer to the exhibit.

An administrator just upgraded to Cisco UCM to version 14 and started SIP implementation with some new SIP trunks. During the testing, an error was reported when making a call. Which action resolves the issue?

Options:

A.

Change to a valid range.

B.

Change DTMF Signaling Method to "RFC 4833*.

C.

Make sure the destination number is configured correctly and the device is registered.

D.

Disable SIP Rel1XX Options.

Question 45

Refer to the exhibit.

An administrator received reports that users do not hear a ringback when they dial specific external numbers. For example, the Cisco Unified Border Element receives a delayed offer invite from Cisco UCM and responds with the 183 session progress in the exhibit. Assume that thePSTN is responsible for generating ringback in these problematic scenarios. Which action resolves the issue?

Options:

A.

Enable early media on the appropriate SIP trunk on Cisco UCM.

B.

Edit the configuration for SIP ReMXX Options in the appropriate SIP profile on Cisco UCM to Send PRACK if 1xx Contains SDP.

C.

On Cisco Unified Border Element: voice service voip sip

Re1xx require 100rel

D.

On Cisco Unified Border Element: voice service voip sip

Re1xx disable 100rel

Question 46

In Cisco Unified Communications Manager, which tool do you use to check SIP traces?

Options:

A.

MTP

B.

CCSIP

C.

RTMT

D.

OS Administration Page

Question 47

Refer to the exhibit.

Users report that outbound PSTN calls from phones registered to Cisco Unified Communications Manager are not completing. The local service provider in North America has a requirement to receive calls in 10-digit format. The Cisco Unified CM sends the calls to the Cisco Unified Border Element router in a globalized E.164 format. There is an outbound dial peer on Cisco Unified Border Element configured to send the calls to the provider. The dial peer has a voice translation profile applied in the correct direction but an incorrect voice translation rule applied, which is shown in the exhibit. Which rule modified DNIS in the format that the provider is expecting?

Options:

A.

rule 1 /^/+\([^1].*\)/ /011\1/

B.

rule 1/^\+1\([2-9]..[2-9]……$\)/ /\1/

C.

rule 1 /^\([2-9]..[2-9]……$\)/ /\1/

D.

rule 1 /^\+1\([2-9]..[2-9]……$\)/ /\0/

Question 48

An engineer is configuring a call park feature in Cisco Unified Communications Manager Express. Which command does the engineer use to ensure that the call is reverted to the user after 60 seconds?

Options:

A.

R2(config-ephone-dn)#park reservation-group 60

B.

R2(config-ephone-dn)#park-slot timeout 60 limit 2 recall alternate 3002

C.

R2(config-ephone-dn)#park reservation-group 1

D.

R2(config-ephone-dn)#park-slot timeout 30 limit 2 recall alternate 3002

Question 49

Refer to the exhibit. Calls from users to the PSTN in an organization get disconnected with a 408 Request Timeout when the called party is unavailable to pick up the call. Which solution must be used to resolve this challenge?

Options:

A.

Configure midcall-signaling preserve-codec.

B.

Choose "Send PRACK" if 1xx contains SDP in the SIP profile.

C.

Configure midcall-signaling passthru media-change

D.

Choose "Send PRACK for all 1xx Messages" in the SIP profile.

Question 50

Exhibit.

Refer to the exhibit. All calls from site A to site B are failing, and the issue has been identified as a media negotiation problem. Which configuration change resolves the issue?

Options:

A.

Disable G.722 on all devices at both sites.

B.

Enable Early Offer on the SIP trunk.

C.

Increase the bandwidth allowance between the RTP_Reg and SJ_Reg regions to 64 kbps.

D.

Create a new audio codec preference list with G.711 U-law 64k as the highest priority and apply it to RTP_Reg and SJ_Reg.

Question 51

Refer to the exhibit.

An engineer configures Cisco Unified Border Element to connect the enterprise VoIP network with a SIP telephony provider. Calls are not working in either direction. What must be configured in the dial peer 1 to fix the issue?

Options:

A.

answer-address 555 ……..

B.

codec g729

C.

session-protocol sipv2

D.

incoming called number 555…….

Question 52

Refer to the exhibit An engineer deploys a Cisco Unified Border Element for SIP trunk interconnection to an ITSP The engineer performs test calls but there is no audio when the called party picks up the phone. What must the engineer do to resolve the issue?

Options:

A.

Disable SIP User Agent bind status (media).

B.

Decrease the SIP max-forwards value to 16.

C.

Disable SIP early-media for 180 responses with SDP

D.

Enable Check media source packets.

Question 53

Refer to the exhibit.

Users report high delays when calling national numbers in the United States. An engineer analyzes the route patterns in Cisco UCM. What must be done to resolve this issue?

Options:

A.

Change the Cisco UCM routing logic to the longest-match algorithm.

B.

Select Allow Overlap Sending for the \+! route pattern.

C.

Mark the \+ [2-9JXX[2-91XXXXXX route pattern with urgent priority.

D.

Set the interdigit timeout service parameter value to 0.

Question 54

Which configuration must an administrator perform to display Translation Pattern operations in Cisco Unified Communications Manager SDL traces?

Options:

A.

Enable the Detailed Call Analysis option under Enterprise Parameters for Unified CM.

B.

Set up the Digit Analysis Complexity in Service Parameters for Cisco Unified CM to TranslationAndAlternatePatternAnalysis.

C.

Check the Translation Patterns Analysis check box in Micro Traces on the Cisco Unified CM Serviceability page.

D.

By default, the Translation Patterns operations are printed in SDL traces, so no additional configuration is necessary.

Question 55

Refer to the exhibit.

How many maximum hops can an ILS update traverse?

Options:

A.

3

B.

6

C.

9

D.

12

Question 56

Cisco UCM has 100,000 entries in the database learned through theILSService. ParameterILSMax Number of Learned Objects in Databasevalue is set to 100,000. What will happen to learned data when the service parameter value is reduced to 50,000?

Options:

A.

Cisco UCM does not write additional ILS learned objects to the database and will delete the first 50,000 entries learned to keep it to the service parameter value.

B.

Cisco UCM does not write additional ILS learned objects to the database and will delete the last 50,000 entries learned to keep it to the service parameter value.

C.

Cisco UCM does not write additional ILS learned objects to the database and keeps the existing database entries.

D.

Cisco UCM will overwrite an entry for newly learned data and keep the parameter value at 100,000.

Question 57

Refer to the exhibit. A collaboration engineer is troubleshooting an issue where a user of a Cisco UCM IP phone reports failed calls when trying to dial out to the PSTN. Which action resolves the issue?

Options:

A.

Assign a calling search space to the line or the device that has access to the route pattern.

B.

Deselect “Block this pattern” on the “Route Option” setting of the route pattern.

C.

Select the “Urgent Priority” setting on the route pattern.

D.

Instruct the user to not dial a “1” before their local area code.

Question 58

Cisco SIP IP telephony is implemented on two floors of your company. Afterward, users report intermittent voice issues in calls established between floors. All calls are established, and sometimes they work well, but sometimes there is one-way audio or no audio. You determine that there is a firewall between the floors, and the administrator reports that it is allowing SIP signaling and UDP ports from 20000 to 22000 bidirectionally. What are two possible solutions? (Choose two.)

Options:

A.

Go to the SIP profile assigned to these IP phones in Cisco Unified CM and change the range of media ports to 16384-32767

B.

Ask the firewall administrator to change the ports to TCP.

C.

Ask the firewall administrator to change the range of UDP ports to 16384-32767.

D.

Go to the SIP profile assigned to these IP phones in Cisco Unified CM and change the range of media ports to 20000-22000.

E.

Go to System Parameters in Cisco Unified Communications Manager and change the range of media ports to 20000-22000.

Question 59

A user’s phone is already configured for Single Number Reach, and the user wants a feature to move an active call from a mobile phone to a desk phone and vice-versa. As an administrator, which additional configuration should be made to fulfill the user’s request?

Options:

A.

Confirm that the desk phone is subscribed to Cisco Extension Mobility.

B.

Check to make sure that the Resume softkey option appears on the desk phone.

C.

Use Dialed Number Analyzer to determine if the user extension can dial the mobile phone.

D.

Add the mobility key to the softkey template that the desk phone is using.

Question 60

A customer has multisite deployments with a globalized dial plan. The customer wants to route PSTN calls via the gateway assigned to each site. Which two actions will fulfill the requirement? (Choose two.)

Options:

A.

Create one route group for each site and one global route list for PSTN calls that point to the local route group.

B.

Create a route group which has all the gateways and associate it to the device pool of every site.

C.

Create one global route list for PSTN calls that points to one global PSTN route group.

D.

Create a hunt group and assign it to each side route pattern

E.

Assign one route group as a local route group in the device pool of the corresponding site.

Question 61

Refer to the exhibit.

An engineer is troubleshooting an issue with the caller not hearing a PSTN announcement before the SIP call has completed setup. How must the engineer resolve this issue using the reliable provisional response of the SIP?

Options:

A.

voice service voip sip send 180 sdp

B.

voice service voip sip rehxx require 100rel

C.

sip-ua

disable-early-media 180

D.

voice service voip sip no reMxx

Question 62

Which services are needed to successfully implement Cisco Extension Mobility in a standalone Cisco Unified Communications Manager server?

Options:

A.

Cisco Extended Functions, Cisco Extension Mobility, and Cisco AXL Web Service

B.

Cisco CallManager, Cisco TFTP, and Cisco CallManager SNMP Service

C.

Cisco CallManager, Cisco TFTP, and Cisco Extension Mobility

D.

Cisco TAPS Service, Cisco TFTP, and Cisco Extension Mobility

Question 63

A company has users that frequently visit locations outside the office. These users need to be able to make calls and keep the company integrity by presenting a company caller ID. The users are equipped with company-paid mobile phones. The company uses Cisco UCM with Cisco Unified Border Element and Expressway-C and Expressway-E for external communications. Which technology must be configured to meet this requirement?

Options:

A.

Cisco Unified SNR

B.

Cisco Unified Mobility

C.

Cisco FindMe

D.

Cisco Roaming Mobility

Question 64

Refer to the exhibit. When setting up a new connection to Cisco UCM, the engineer must use out-of-band DTMF. Which configuration meets this requirement?

Options:

A.

dtmf-relay h245-alphanumeric

B.

dtmf-relay sip-kpml

C.

dtmf-relay cisco-rtp

D.

dtmf-relay rtp-nte

Question 65

Which two extended capabilities must be configured on dial peers for fast start-to-early media scenarios

(H.323 to SIP interworking)? (Choose two.)

Options:

A.

DTMF

B.

BFCP

C.

VIDEO

D.

FAX

E.

AUDIO

Question 66

Which configuration element of a hunt group allows for changing Calling Party Transformations settings?

Options:

A.

line group

B.

hunt pilot

C.

route group

D.

hunt list

Demo: 66 questions
Total 221 questions